What Is Hacking Seconds and Why Does It Matter?

Updated

Hacking seconds means the seconds hand stops when you pull out the crown. It lets you set a mechanical watch to the exact second against a reliable time source. The Miyota 9039 hacks, as do most mechanical movements made today.

Watchmakers also call the feature stop seconds. You will see both terms on specification sheets, and they mean the same thing.

What hacking actually does

In a mechanical watch, the balance wheel swings back and forth and lets energy out of the mainspring in steady beats. Stop the balance and the whole watch stops, seconds hand included.

A hacking movement has a small lever, often called a stop lever or brake, linked to the crown. Pull the crown out to the time-setting position and the lever touches the balance wheel and holds it still.

Push the crown back in and the lever lets go. The balance starts swinging again and the watch runs on from exactly where it stopped.

Because the lever stops the balance rather than the hands, the whole movement pauses together. Nothing slips, and the hands stay exactly in step with each other.

Without hacking, the seconds hand keeps moving while you set the time. You can line up the hours and minutes, but the seconds will always be a little out.

Where hacking comes from

The idea grew up around synchronised timekeeping. On ships, a hack watch was set against the marine chronometer, which was kept safely below decks. A navigator could then carry the hack watch on deck to time sightings of the sun and stars.

In the Second World War, Allied airmen synchronised their watches in the briefing room before heading to their aircraft. This became known as a time hack. Military watch specifications, such as the American A-11, called for a seconds hand that could be stopped and set.

The same idea worked for any group that could not talk once a mission began. Every watch was set to one reference and started together.

The link to coordinated operations feels familiar to us. The KOMPAS dial takes its twelve five-minute segments from the RAF Fighter Command sector clock, used in the 1940 operations rooms. Our note on the RAF sector clock tells that story.

How to set a watch to the second

  1. Find a reliable time source. Your phone clock is set automatically by the network and is accurate enough for most people.
  2. If the watch has stopped, wind it first. On the Miyota 9039, turn the crown clockwise in its normal position until the seconds hand starts to move.
  3. Wait for the seconds hand to reach the 12 marker, then pull the crown out to the time-setting position. The seconds hand stops at the top.
  4. Turn the crown to set the hour and minute hands. Place the minute hand exactly on the next minute marker after your reference time.
  5. Watch your reference clock. As it reaches that new minute, push the crown back in.
  6. Check again a minute later. The two seconds hands should now move together.

If you miss the moment, simply pull the crown again and repeat. There is no harm in trying a few times.

If you prefer a broadcast signal, the six BBC pips work well. The hour starts at the beginning of the sixth, longer pip. Use analogue radio, though, because digital radio and streaming add a delay of a few seconds.

Our guide to winding and setting an automatic watch covers crown positions and winding in more detail.

Which movements hack

Most mechanical movements made today hack. If a specification sheet lists stop seconds, the watch hacks. A few well-known calibres show the pattern.

  • Miyota 9039 automatic (Citizen group). Hacks and winds by hand. It runs at 28,800 vibrations per hour and powers every KOMPAS.
  • ETA 2824-2. A widely used Swiss automatic that hacks and winds by hand.
  • Sellita SW200-1. Hacks and winds by hand, and is a common alternative to the ETA 2824-2.
  • Seiko NH35. Hacks and winds by hand, and appears in many affordable automatics.
  • Seiko 7S26. Does not hack and cannot be wound by hand. It powered earlier Seiko 5 and SKX models.

The Miyota 9039 also winds by hand, which pairs well with hacking. You can wind a stopped watch, set it to the second and be ready to go within a minute.

Some movement families changed over time. Miyota added a stop-seconds device to its 82 series automatics around 2018 to 2019, so older examples do not hack. If you buy second-hand, check the exact calibre and its age.

Plenty of good watches do not hack, and that is fine for casual wear. You simply set them to the nearest few seconds and accept a small offset.

Why hacking matters

  • Precise setting. You can match a reference clock to the second, not just the minute.
  • Checking accuracy. Set the watch exactly, then compare it with the same source a day later. You will see how many seconds it gains or loses.
  • Timing short tasks. A perfectly set seconds hand makes it easier to time a call, a parking meter or a boiled egg.
  • Synchronising with others. A group can set their watches together, as navigators and aircrews once did.
  • Less fiddling. Owners of non-hacking watches sometimes turn the hands backwards to nudge the seconds into line. This is called back hacking, and makers advise against doing it often.

Hacking does not make a watch more accurate by itself. It lets you start from a perfect setting and see the true rate.

A KOMPAS keeps time to within a few seconds a day. With hacking you can check that for yourself over a week. Try it on the West or any of the four models, which share the same movement.

Use hacking to check your watch's rate

  1. Wear the watch as normal for a day so it is well wound.
  2. Hack it and set it to the exact second against your phone.
  3. Check it at the same time the next day and note how many seconds it has gained or lost.
  4. Repeat for a few days, as wear and position change the result slightly.
  5. Average the figures to find the watch's true daily rate.

Rest position matters overnight too. Leaving a mechanical watch dial up or crown down can change the next day's rate a little. Some owners use that to nudge the time back into line.

Hacking and quartz watches

The term belongs mainly to mechanical watches, because they have a balance wheel to stop. On most analogue quartz watches, pulling the crown also stops the seconds hand, so setting to the second works in much the same way.

Either way, the goal is the same. Start from a perfect setting and the watch shows its true rate.

Frequently asked questions

What does hacking mean on a watch?

Hacking means the seconds hand stops when you pull the crown out to set the time. It starts again when you push the crown back in.

Does the Miyota 9039 hack?

Yes. The Miyota 9039 has hacking seconds and hand winding, so you can stop the seconds hand and set the watch to the exact second.

Is it bad to stop a watch with the hacking feature?

No. Hacking is designed for everyday use. A small lever simply holds the balance wheel still until you push the crown back in.

What is back hacking?

Back hacking means turning the hands slightly backwards to nudge a non-hacking seconds hand into line. Makers advise against doing it often.

How do I check my watch's accuracy?

Hack the watch and set it to the second against a reliable clock. Compare it again at the same time the next day and note the difference.

Every KOMPAS hacks, winds by hand and keeps time to within a few seconds a day. See the KOMPAS range.

Previous
Previous

How to Measure Your Wrist for a Watch

Next
Next

Automatic or Quartz Watch? How to Choose the Right One