28,800 vph Explained – What a Watch’s Beat Rate Means

Updated · By Adventure Man

28,800 vph means the balance wheel in a mechanical watch beats 28,800 times an hour. 8 beats a second, which watchmakers also write as 4 Hz. A higher beat rate gives a smoother-looking seconds hand and tends to make timekeeping steadier, at the cost of using a little more energy.

You will see the number on spec sheets everywhere, including ours – the Miyota 9039 inside every KOMPAS runs at 28,800 vph. Here is what it actually means, how it compares with 21,600 and 36,000, and how much it should matter when you choose a watch.

What vph means

At the heart of a mechanical movement is the balance wheel, a small weighted wheel on a fine hairspring that swings back and forth at a steady rate. Each swing in one direction is one beat (also called a vibration or an alternation). Every beat lets the escapement release the gear train by a tiny step, which is the tick you hear and the little jump you see in the seconds hand.

"vph" is vibrations per hour. You will also see "bph" (beats per hour) or "A/h" (alternations per hour). They all mean the same thing.

vph and Hz – the conversion

Hertz counts full oscillations – the balance swinging one way and back again. One full oscillation is two beats. So.

  • Beats per second = vph ÷ 3,600.
  • Hz = vph ÷ 7,200 (or half the beats per second).

That is why 28,800 vph is 8 beats a second but 4 Hz. The two figures describe the same speed counted in different ways.

Beat rate (vph)FrequencyBeats per secondWhere you see it
18,0002.5 Hz5Many older and vintage movements
21,6003 Hz6Workhorse automatics such as the Miyota 8215 and Seiko NH35
28,8004 Hz8The modern norm. Miyota 9039, ETA 2824-2, Sellita SW200-1
36,0005 Hz10High-beat movements such as the Zenith El Primero

Sweep – why higher looks smoother

A mechanical seconds hand does not truly glide. It moves in tiny steps, one per beat. At 5 beats a second you can see the steps if you look closely. At 6 the motion is smoother, at 8 it reads as a near-continuous sweep, and at 10 it is smoother still.

A quartz watch, by contrast, usually jumps once a second, which is why the sweep of a mechanical seconds hand is one of the first things people notice. If the seconds hand on your automatic looks slightly steppy in a close-up video, that is normal – you are seeing individual beats.

There is a practical side too. Each step at 8 beats a second is an eighth of a second, so a 4 Hz watch can, in principle, be read to the nearest eighth. That is why high-beat movements suit chronographs. Zenith describes its 5 Hz El Primero 3600 as giving a true tenth-of-a-second measurement.

Beat rate and accuracy

A faster balance carries more momentum through each swing and is harder to disturb. In practice, that tends to make a higher-beat movement less sensitive to knocks, wrist movement and changes of position, so its rate stays steadier through the day.

But beat rate is only one part of accuracy. How well the movement is regulated, the quality of the hairspring, temperature, how fully the mainspring is wound and how you wear it all matter as much or more. A well-regulated 3 Hz watch can keep better time than a carelessly regulated 4 Hz one.

Makers' published tolerances give a hint of the difference within one family. Miyota quotes −10 to +30 seconds a day for the 28,800 vph 9039, and −20 to +40 seconds a day for the 21,600 vph 8215. Those are factory tolerances, not typical results. Most watches run well inside them, and our Miyota 9039 explainer covers what to expect in daily wear.

Beat rate and power reserve

Every beat takes a little energy from the mainspring. Beat faster with the same spring and the watch runs down sooner. Higher rates also mean more work for the escapement and its oils over the years.

In practice, designers balance this with the spring, the gear train and the balance itself, so the beat rate alone does not tell you the power reserve. The Miyota 9039 (28,800 vph) and the Miyota 8215 (21,600 vph) are both quoted at about 42 hours. And the Zenith El Primero 3600 runs at a quick 5 Hz yet has a 60-hour power reserve, about ten hours more than the original El Primero.

Common movements and their beat rates

MovementBeat rateFrequencyPower reserve
Miyota 903928,800 vph4 HzAbout 42 hours
Miyota 821521,600 vph3 HzAbout 42 hours
Seiko NH3521,600 vph3 HzAbout 41 hours
ETA 2824-228,800 vph4 HzAbout 42 hours
Sellita SW200-128,800 vph4 HzTypically 41 hours (at least 38)
Zenith El Primero 360036,000 vph5 Hz60 hours

Figures checked on 19 November 2026 from each maker's own specification pages (Miyota, ETA, Sellita, Zenith), with the NH35 from its published technical data and the El Primero 3600 power reserve from independent coverage of its launch.

How to check a watch's beat rate

The spec sheet is the easiest way. If you want to see it for yourself, a timing app on your phone (or a watchmaker's timegrapher) listens to the ticks and shows the beat rate, how fast or slow the watch is running and how evenly it beats. It is a fun way to see how your watch behaves when it is face up, crown down or nearly run down.

You can also count by ear, if your hearing is sharp and the room is quiet. Eight ticks a second is too fast to count comfortably, but you will hear the difference between a 3 Hz and a 4 Hz watch side by side.

Does beat rate matter when buying?

A little, but less than the spec-sheet attention suggests. As a rough guide.

  • 21,600 vph (3 Hz) is perfectly good. Plenty of reliable workhorse movements run at this rate.
  • 28,800 vph (4 Hz) is the modern standard for good automatics – a smooth sweep and steady timekeeping without a big power penalty.
  • 36,000 vph (5 Hz) is a specialist choice, mostly for chronographs and those who love the sweep.

Look at the whole watch instead – the movement's reputation and serviceability, the power reserve, hacking seconds, the case, the crystal and the dial you will read every day. We chose the 28,800 vph Miyota 9039 for the KOMPAS North and the rest of the range because it combines that smooth 8-beat sweep with hacking seconds, hand-winding and no date, so there is no unused date position on the crown. If you are comparing watches that share it, see our round-up of the best Miyota 9039 watches.

Frequently asked questions

What does 28,800 vph mean?

It means the balance wheel beats 28,800 times an hour, which is 8 beats a second or 4 Hz. Each beat moves the seconds hand on by a tiny step.

Is 28,800 vph better than 21,600 vph?

It gives a smoother sweep and tends to make timekeeping steadier, but it is not automatically more accurate. Regulation and build quality matter as much, and plenty of reliable workhorse movements run at 21,600 vph.

What is the difference between vph and Hz?

vph counts single beats per hour. Hz counts full back-and-forth oscillations per second, and one oscillation is two beats. Divide vph by 7,200 to get Hz. 28,800 vph is 4 Hz.

Does a higher beat rate reduce power reserve?

With everything else equal, yes, because each beat uses energy. In practice designers compensate, so a 28,800 vph Miyota 9039 and a 21,600 vph Miyota 8215 both run for about 42 hours.

Why does my automatic seconds hand move in small steps?

Because it moves once per beat. At 8 beats a second the steps are tiny, so it looks like a sweep, but in a slow-motion video you can see them. That is normal.

What beat rate does a KOMPAS watch use?

Every KOMPAS uses the Miyota 9039 automatic movement, which runs at 28,800 vph (8 beats a second, 4 Hz) with about 42 hours of power reserve.

See 8 beats a second for yourself – the KOMPAS North, with an exhibition caseback, or browse all four colours.

Next
Next

Mechanical Watch vs Smartwatch for Hiking and Travel (2026)