How to Wind and Set an Automatic Watch – A Miyota 9039 Guide

Updated · By Adventure Man

To wind a stopped Miyota 9039, leave the crown pushed in and turn it clockwise – about 15 to 20 turns gets it ticking, and around 40 gives it a full wind. To set the time, pull the crown out to its one setting position, which stops the seconds hand, turn the hands to the right time and push the crown back in.

That takes less than a minute. Below are the details – what each crown position does, how to set the watch to the second, and what to do when it has stopped in a drawer.

Everything here applies to the Miyota 9039, the automatic movement inside every KOMPAS, and most of it applies to any modern automatic watch. If you want the full specification first, read Miyota 9039 explained.

How an automatic watch stays wound

An automatic watch runs on a coiled mainspring. As the spring slowly unwinds it drives the gears, the balance wheel and, in the end, the hands. Inside the case a weighted half-disc called the rotor swings round as you move your arm and winds the spring back up. On a KOMPAS you can watch it turn through the exhibition caseback.

You can also wind the spring by hand through the crown. Both routes fill the same spring, so hand-winding is not a different mode, just a quicker way to top up. When the spring is full, the Miyota 9039 will run for about 42 hours before it stops.

Crown positions on the Miyota 9039

Many automatics have three crown positions – pushed in, a middle click for the date and fully out for the time. The Miyota 9039 has no date, so it only needs two. Miyota's own instruction sheet calls them position A (winding) and position B (time setting).

Crown positionWhat it doesSeconds handWhen to use it
Pushed in (position A)Winds the mainspring when you turn the crown clockwiseRuns normallyEvery day. This is where the crown should sit when you wear the watch
Pulled out one click (position B)Moves the hour and minute handsStops (hacking)Setting the time, or syncing to the second

Crown positions and winding turns from Miyota's 9039 instruction and specification sheets, checked on 19 November 2026.

Because there is no date, there is also no "phantom" position. Some no-date watches use a movement built for a date and simply leave the date wheel out, which leaves a middle crown click that does nothing. The 9039 is a no-date calibre with only two positions, so every click on the crown has a job.

How to hand-wind a stopped watch

If your watch has stopped, or you have just taken it out of the box, give it a proper start by hand rather than relying on the rotor. A stopped automatic on a quiet wrist can take a long time to build up enough power to run well.

  1. Take the watch off your wrist. Winding on the wrist puts sideways pressure on the crown and stem.
  2. Check the crown is pushed fully in (position A).
  3. Hold the case in one hand and turn the crown clockwise with your thumb and finger, rolling the top of the crown towards 12 o'clock.
  4. Count turns. Miyota's instruction sheet says 15 to 20 turns gets the seconds hand moving. Its specification sheet gives about 40 turns as a full wind.
  5. Stop at around 40. You will not hit a hard stop, because automatic mainsprings are built to slip once they are full so the rotor cannot overwind them, but there is no benefit in carrying on.
  6. Set the time (see below), push the crown home and put the watch on.

Wind smoothly. If the crown feels gritty, stiff or loose, stop and have a watchmaker look at it.

Do you need to hand-wind every day?

No. If you wear the watch most days, the rotor does the work. Hand-winding is for starting a stopped watch, or for topping up on a day when you will be sitting still for hours. Every turn adds a little wear to the winding parts, so there is no need to make it a daily ritual.

How to set the time to the second

The 9039 has hacking seconds – when you pull the crown out to position B, the seconds hand stops dead. That lets you line the watch up with a reference time exactly.

  1. Wait until the seconds hand reaches 12, then pull the crown out one click. The seconds hand stops at 12.
  2. Turn the crown to move the minute hand a minute or two past the time you want, then bring it back to the exact minute. Finishing with a slight backwards move takes up any slack in the gears, so the minute hand sits squarely on its marker.
  3. Check the hour hand. On a KOMPAS the inner 13–24 track means the hour hand reads both 1 and 13 at once, so there is no morning or evening to get wrong.
  4. Watch your reference clock (a phone or a radio time signal). As it reaches the top of the minute, push the crown back in. The seconds hand starts and the watch is set.

If you want to read the 24-hour scale properly, our guide to how to read a 24-hour dial walks through it.

Why no date makes setting simpler

On a watch with a date, there is a window of time when you should not touch the quick-set date. Around midnight the movement starts engaging the date wheel over several hours. If you force the date forward with the crown while that is happening, you can damage the date mechanism. Many makers give a rough "danger zone" of about 9 pm to 3 am, though the exact window varies by movement, and the usual advice is to move the hands to around 6:30, set the date, then set the time.

The 9039 has none of this. With no date and a printed 24-hour track, you can set a KOMPAS at any time of day, in any direction, and the only thing that can be wrong is the time itself.

Wearing it to keep it wound

A watch worn daily usually stays wound without help, though a day on your feet winds it more than a day at a desk. If you notice your watch stopping overnight after a quiet day, give it 15 to 20 turns in the morning, or a few more in the evening, and it will carry on.

With about 42 hours of reserve, a full spring carries the watch through a night off the wrist and most of the next day. Take it off on Friday evening and leave it until Monday, though, and you will probably need to wind and set it again.

Do you need a watch winder?

A watch winder is a box that turns the watch slowly to keep the rotor working while you are not wearing it. It is a convenience, not a requirement – letting an automatic stop does not hurt it.

A winder makes most sense if you rotate several automatics and do not want to reset each one before you wear it. If you use one, pick the gentlest setting that keeps the watch running, and keep the winder away from speakers and other magnetic sources, since the motor and the watch both sit inside it. Our automatic watch care guide explains why magnetism matters.

What to do if your watch stops

If it stopped after a day or two off the wrist, it has simply run out of reserve. Wind, set and wear it.

If it stops while you are wearing it every day, or runs for much less time than it should after a full wind, something needs attention. Common causes are a magnetised hairspring (which usually shows up as the watch suddenly running fast) or old lubricants, which come with age and lack of servicing. The care guide linked above has a symptom table. If in doubt, contact us, since every KOMPAS comes with a 2-year international warranty.

Frequently asked questions

How many turns does it take to wind a Miyota 9039?

Miyota says 15 to 20 clockwise turns gets a stopped 9039 running, and about 40 turns gives a full wind, which is good for roughly 42 hours.

Can I overwind an automatic watch?

Not in normal use. Automatic mainsprings are designed to slip once they are full, so neither the rotor nor the crown can wind them too tight. There is still no point turning the crown much past a full wind.

Which way do I turn the crown to wind it?

With the crown pushed in, turn it clockwise, rolling the top of the crown towards 12 o'clock.

Why does the seconds hand stop when I pull the crown out?

That is hacking. The 9039 stops the balance when the crown is in the time-setting position, so you can set the watch to the exact second against a reference clock.

Is it bad to let an automatic watch stop?

No. Letting it stop between wears does no harm. Wind it by hand when you pick it up again, set the time and wear it.

Does the KOMPAS have a date to set?

No. The Miyota 9039 in every KOMPAS has no date, so there is no date to set, no midnight danger zone and no unused crown position.

Two crown positions, no date, nothing to get wrong – see the KOMPAS North.

Previous
Previous

How to Change a 20 mm Quick-Release Strap – and Rubber vs Nylon

Next
Next

How to Read the 13–24 Track on a Field Watch Dial