How to Change a 20 mm Quick-Release Strap – and Rubber vs Nylon

Updated · By Adventure Man

To change a 20 mm quick-release strap, slide the small lever on the spring bar inwards, lift that end of the strap out of the lug, and repeat on the other side. To fit one, drop one end of the bar into its lug hole, pull the lever, line up the other end and let go. It takes about a minute, needs no tools, and the only real rule is to tug-test every strap before you wear it.

Every KOMPAS comes with two straps, one rubber and one nylon, both 20 mm and both quick-release. This guide shows you how to swap them, how to check what width you need if you buy more, and which material suits which day.

How quick-release spring bars work

A spring bar is a short metal tube with a spring inside and a pin at each end. The spring pushes the pins outwards into small holes drilled in the inside faces of the lugs, which holds the strap in place.

On a standard strap, you compress the pins with a forked spring bar tool, working blind between the strap and the case. A quick-release bar does the same job, but one of the pins has a small lever (sometimes called a switch or tab) that sticks out of the back of the strap. Slide the lever towards the middle of the strap and the pin retracts. No tool, no prying, and far less chance of scratching the lugs.

The bar stays attached to the strap when you take it off, so there is nothing small to lose.

How to take a strap off

  1. Lay the watch face down on something soft – a folded towel, a microfibre cloth or a mouse mat. This protects the sapphire crystal and the case, and stops the watch sliding about.
  2. Find the quick-release lever on the underside of the strap, close to the lugs.
  3. With your fingernail or fingertip, slide the lever towards the centre of the strap. You will feel the pin retract.
  4. Keeping the lever pulled, lift the strap end up and away from the lug. The other pin will slide out of its hole on its own.
  5. Repeat on the other half of the strap.

How to fit a strap

  1. Hold the strap so the lever faces the back of the watch. On a two-piece strap, the half with the buckle usually goes at 12 o'clock and the half with the holes at 6 o'clock.
  2. Seat the fixed pin (the end without the lever) into its lug hole first.
  3. Pull the lever to retract the other pin, swing that end of the strap down between the lugs and line the pin up with the hole.
  4. Release the lever slowly. You should feel, and often hear, a small click as the pin drops into the hole.
  5. Tug the strap firmly away from the case, then twist it gently side to side. It should not move or spring out.
  6. Repeat for the other half, then tug-test both again before you put the watch on.

Safety tips

  • Tug-test every time. A pin that is sitting on the edge of its hole rather than in it can feel secure until it catches on a sleeve. Ten seconds of pulling saves a watch on the pavement.
  • Work over a soft surface. If a strap slips, the watch lands on a towel rather than a tiled floor.
  • Keep your face clear. Spring bars are under tension. If one escapes your fingers it can fly off, so do not work with the watch right under your eyes.
  • Do not force it. If the pin will not line up, retract the lever again and reposition. Pushing hard can bend the bar.
  • Check old bars. If a spring bar feels weak, is bent or shows rust, replace it rather than trusting it.

How to measure lug width

Lug width is the gap between the inside faces of the two lugs, where the strap sits. It is almost always given in whole millimetres, and it is the number to look for when you buy a strap. The KOMPAS is 20 mm.

For any other watch, the easiest way is to measure with a ruler or a pair of digital callipers across the gap at the point where the spring bar sits. If you have the strap off, you can also measure the width of the strap end. A strap a millimetre too narrow will slide about between the lugs. One a millimetre too wide will not go in without being squashed.

Lug width is a different number from case diameter. A 39 mm watch can take 20 mm straps, as the KOMPAS does, but other 39 mm watches use 19 mm or 21 mm, so always check. If you are still deciding on case size, our guide to whether a 39 mm watch is right for your wrist covers the measurements that matter.

Rubber vs nylon vs leather

There is no best strap, only the best one for what you are doing. Here is how the three common materials compare.

MaterialWaterComfortWeightCareBest for
RubberFully at home in water. Does not absorb itSoft and grippy. Can feel warm in heatLight to mediumRinse in fresh water and wipe drySwimming, rain, sweaty hikes, travel
NylonFine for a soaking, but holds water and takes a while to dryBreathable and flexible. Easy to wear all dayLightestHand-wash in mild soapy water and air-dryEveryday wear, warm days, long walks
LeatherAvoid. Water stains it, swells it and shortens its lifeMoulds to the wrist over timeMediumKeep dry. Wipe with a damp cloth and let it rest between wearsOffice, evenings, dry weather

A general guide. Individual straps vary with thickness, lining and finish.

Rubber

Rubber is the strap for water and weather. It shrugs off rain, sea, pools and sweat, and a quick rinse gets it clean. The KOMPAS is water resistant to 100 m, and the rubber strap is the one to pair with that when you are actually in the water. See 100 m water resistance explained for what that rating does and does not mean.

Nylon

Nylon is the field-watch classic – light, breathable and quietly practical. It is the most comfortable choice for hot days and long days because air gets through it and it never feels sticky. It will survive a downpour, but it holds water for a while afterwards, so swap to rubber if you know you will be swimming.

Leather

KOMPAS does not include a leather strap, but because the lugs are a standard 20 mm and the bars are quick-release, you can fit almost any 20 mm leather strap you like. Leather looks more formal and ages well, but it does not like water, heat or heavy sweat. Keep it for dry days.

When to wear which

  • Beach, pool or boat – rubber.
  • Hiking, cycling or a long day outdoors – nylon in the dry, rubber if it is wet or you sweat a lot.
  • Work or a desk day – nylon, or a leather strap of your own.
  • Travel – wear one, pack the other. Quick-release means you can swap in a hotel room in a minute.
  • Dinner or a wedding – leather, if you have one. Otherwise the nylon reads more relaxed and the rubber more sporty.

The black accents of the KOMPAS North go with almost any strap colour, while the green East suits olive and khaki nylon especially well.

Frequently asked questions

Do I need a tool to change a quick-release strap?

No. The lever on the spring bar retracts the pin with a fingertip. You only need a spring bar tool for straps with standard bars.

What lug width is the KOMPAS?

20 mm. Both straps in the box, rubber and nylon, are 20 mm quick-release, and most other 20 mm straps will fit too.

How do I know the strap is fitted properly?

Release the lever slowly until the pin clicks into its hole, then tug the strap firmly away from the case and twist it gently. If it does not move, it is seated. Check both halves.

Can I swim with the nylon strap?

You can, and it will not be damaged, but it holds water and takes a while to dry. Rubber is the better choice for swimming.

Can I fit a leather strap to a KOMPAS?

Yes. Most 20 mm straps will fit. Quick-release leather straps are the easiest to swap. Standard ones need a spring bar tool.

Two straps in the box, swappable in a minute – see the KOMPAS range.

Previous
Previous

Automatic Watch Care (2026) – Servicing, Magnetism and Everyday Knocks

Next
Next

How to Wind and Set an Automatic Watch – A Miyota 9039 Guide