Updated
To change a strap with a spring bar tool, slide the fork between strap and lug and push the bar in to free it. To fit the new one, seat one end of the bar, compress the other and let it snap into the lug hole. With care, the whole job takes about five minutes.
A spring bar tool is the most useful small tool a watch owner can have. It costs little, fits in a drawer and turns a strap change into a calm, five-minute job. This guide covers classic spring bars, the steps and how to keep your case free of scratches.
What a spring bar is
A spring bar is a small steel tube with a spring inside and a pin at each end. The pins push outwards into small holes on the inside of the lugs.
Press the pins in and the bar comes free. Release them and they spring back into place.
Most spring bars have flanges, small raised collars near each end. The fork of the tool hooks behind a flange to compress the bar.
The standard diameter is 1.8 mm. Thinner and thicker bars exist for particular straps and watches, so match the size you remove.
Some watches have drilled lugs, with holes that go right through to the outside. On these, you push the pin from outside with the pointed end of the tool.
Classic spring bars vs quick release
A classic spring bar has no lever. You need a tool to compress it.
A quick-release bar has a small lever on its side. You pull the lever with a fingernail and the strap comes away without any tool.
Quick release is ideal if you swap straps often. Classic bars suit straps that stay on for longer, and they work on almost every watch.
Every KOMPAS ships with a rubber strap and a nylon strap on 20 mm quick-release bars. For those, follow our guide to changing a 20 mm quick-release strap instead.
Many fine straps still use classic spring bars. The G.L.C. × KOMPAS DPM Strap is one of them, and it comes in its own box with a spring bar tool.
What you need
- A spring bar tool with a fork at one end and a pin at the other
- A soft cloth or microfibre mat to work on
- Low-tack masking tape to cover the lugs
- Good light and a clear table, ideally with a tray to catch a stray bar
- Your new strap, checked for the right width
Check the width before you start. Our guide to lug width shows how to measure in a minute.
How to remove the old strap
- Lay the watch face down on the cloth, with the strap stretched out flat.
- Cover the inner faces of the lugs with small strips of tape.
- Slide the fork end between the strap and the lug, along the line of the spring bar.
- Hook the fork behind the flange nearest the lug.
- Push the bar gently towards the centre of the case until the pin leaves its hole.
- Tilt the strap away from the lug and let the bar ease out. Keep a finger over it so it cannot spring away.
- Repeat on the other half of the strap.
With drilled lugs, push the pin from outside with the pointed end instead. Wiggle the strap gently as the pin clears the hole.
Put the old bars somewhere safe. If they are in good condition, they make useful spares.
How to fit the new strap
- Slide a spring bar through the end of the new strap so it sits centred.
- Check which half goes where. Most two-piece straps put the buckle half at twelve o'clock and the long half at six.
- Seat one pin of the bar in its lug hole.
- Compress the other pin with the fork.
- Lower that end between the lugs until the pin lines up with its hole.
- Release slowly and feel the pin snap into place.
- Repeat for the other half of the strap.
Then test it. Tug each half firmly and try to slide the bar sideways. A properly seated bar will not move.
If a bar feels loose, take it out and refit it. It is far better to spend another minute now than to lose a watch later.
How to avoid scratches
Most scratches come from a tool that slips under pressure. A little preparation prevents almost all of them.
- Tape the lugs before you start. It is cheap insurance for a polished or sandblasted finish.
- Work slowly and use light pressure. A steady push beats a sharp shove.
- Keep the fork angled towards the strap, not the case.
- Work over a soft surface so a dropped watch lands safely.
- Never force a strap that is too wide. Squeezing it in can mark the inside of the lugs.
Good light helps more than you might think. You need to see the flange and the lug hole clearly.
Common mistakes to avoid
Most strap changes go wrong in the same few ways. Knowing them in advance saves time, scratches and lost parts.
- Working over a carpet. A spring bar that flies off is almost impossible to find.
- Pushing the fork against the case instead of the flange. This is the usual cause of a scratched lug.
- Fitting the strap upside down. Check that the buckle half sits at twelve o'clock before you seat the second bar.
- Skipping the tug test. A bar that looks seated may be resting on the edge of its hole.
- Reusing a tired bar. If the spring feels soft or gritty, fit a new one.
- Buying the wrong width. A strap that does not match the lugs will never sit right, however carefully you fit it.
Take your time on the first change. After two or three, the whole process becomes second nature.
When to replace a spring bar
Spring bars are cheap, and they do wear. Replace any bar that feels weak, is bent or has a pin that sticks.
Bars on older watches can break during removal. If you own a vintage piece, fit fresh bars whenever you change the strap.
Keep a few spares in your size. Match both the length to your lug width and the diameter to the strap.
A strap change is also a good moment for a quick clean. Wipe the lugs and the case back with a soft cloth before the new strap goes on.
All four of our watches use 20 mm lugs. The West, with its city-red dial, takes any good 20 mm strap with standard spring bars.
For more on keeping a mechanical watch in good order, read our notes on automatic watch care and servicing.
Frequently asked questions
Do I need a spring bar tool to change a strap?
For classic spring bars, yes. Quick-release straps have a small lever, so you can change them by hand.
Which end of the spring bar tool should I use?
Use the fork for most straps, hooked behind the flange. Use the pointed end on drilled lugs, pushing the pin from outside.
Can I reuse old spring bars?
Yes, if they are straight and spring back firmly. Replace any bar that is bent, weak or sticky.
How do I avoid scratching the lugs?
Cover the lugs with low-tack tape, work on a soft cloth and keep the tool angled towards the strap.
Does the DPM strap come with a spring bar tool?
Yes. The DPM strap comes in its own box with a spring bar tool and a story card.
Every model takes 20 mm straps and ships with two of them. See the KOMPAS range.