How to Measure Your Wrist for a Watch

Updated

Wrap a soft tape measure, or a strip of paper, around your wrist where you wear a watch and read the length in centimetres. Then compare a watch's lug to lug, not just its case diameter, with the flat top of your wrist. If the lugs stay on that flat area, the watch will sit well.

Two numbers do most of the work. Your wrist circumference tells you about strap length and general scale. The width of the flat top of your wrist tells you how long a watch you can wear.

Measure with a tape

Measure the wrist you wear your watch on. Most people wear a watch on their non-dominant hand, and the two wrists can differ slightly.

  1. Use a soft tailor's tape measure.
  2. Wrap it around your wrist where the watch sits, just beside the wrist bone.
  3. Keep it snug against the skin, but not tight.
  4. Read the measurement in centimetres where the tape meets the zero end.
  5. Measure again later in the day. Wrists swell slightly with heat and activity, so the larger figure is the safer one.

No tape? Use paper

  1. Cut a strip of paper about 1 cm wide and 25 cm long.
  2. Wrap it around your wrist in the same place, snug but not tight.
  3. Mark the point where the end overlaps with a pen.
  4. Lay the strip flat against a ruler and measure up to the mark.

Paper works better than string because it does not stretch. If you do use string, pull it gently and measure twice.

Measure the flat top of your wrist

Circumference is useful, but fit depends more on the flat top of your wrist, where the case sits. Two wrists with the same circumference can have very different shapes.

Look down at your wrist and hold a ruler across it, from the thumb side to the little-finger side. Measure the flat area before the wrist starts to curve away at each edge. Note that figure in millimetres. A friend can help here, as it is easier to read the ruler from above.

A flat, wide wrist carries a longer watch than a round one of the same size. That is why a friend's watch can look perfect on them and oversized on you.

Case diameter vs lug to lug

Case diameter is the width of the case, usually measured without the crown. It is the number most brands lead with, and it gives a rough sense of size.

Lug to lug is the distance from the tip of the top lugs to the tip of the bottom lugs. It decides how much of your wrist the watch covers from end to end.

If the lug tips hang over the edges of the flat top, the case can rock. The strap can also kink or leave a gap. The watch will feel unstable even if its diameter looks modest on paper.

That is why a 39 mm watch with long, straight lugs can wear larger than a 41 mm watch with short, curved ones. For fit, lug to lug is the better guide.

Crown size matters a little too. A large crown can dig into the back of your hand on a small wrist.

Thickness also counts. A slim case sits under a shirt cuff and feels smaller than its diameter suggests. A tall case sits higher and looks bigger.

Lug width is a different measurement again. It is the gap between the lugs, which sets the width of the strap. Our note on lug width explains how it affects comfort and strap choice.

A rough size table

Use this as a starting point, not a rule. Wrist shape, case shape and strap all change how a watch wears.

Wrist circumferenceComfortable lug to lug
Under 15 cmAbout 42 to 46 mm
15 to 16.5 cmAbout 44 to 48 mm
16.5 to 18 cmAbout 46 to 50 mm
18 to 19.5 cmAbout 48 to 52 mm
Over 19.5 cmAbout 50 mm and up

Your flat-top measurement is the final check. If a watch's lug to lug is no longer than that width, it should sit well on your wrist.

If you are between two rows, look at the case shape. Curved lugs and a slim case let you go a little longer. Straight lugs and a thick case call for a shorter watch.

Preview a watch with paper

You can preview a watch before you buy it. Draw a rectangle on card as long as the lug to lug and as wide as the case. Cut it out, lay it on your wrist and look in a mirror.

It is a rough test, but it shows at once whether the lugs reach the edges. Try 46.5 mm by 39 mm to see how a KOMPAS would sit.

Common sizing mistakes

  • Judging by case diameter alone. Two 40 mm watches can wear very differently.
  • Measuring too loosely. A loose tape adds length you will not use on the strap.
  • Forgetting thickness. A tall watch catches on cuffs and looks larger.
  • Ignoring the strap. A thick, stiff strap makes a watch wear bigger, while a soft strap hugs the wrist.
  • Copying a friend. Wrist shape varies a lot, even between people with the same measurement.

Where a KOMPAS fits

Every KOMPAS has a 39 mm sandblasted steel case, 46.5 mm lug to lug and a thickness of 10.4 mm. On the table above, that suits wrists from roughly 15 cm to 18 cm. On larger wrists it reads as a classic, understated field watch.

The 20 mm lug width takes the supplied rubber and nylon straps, both with quick-release spring bars. You can swap between them in seconds without tools.

Rubber stays put in water and heat. Nylon is light and breathable, and it dries quickly. Our strap materials guide compares the options in more depth.

If you are still unsure, read our guide to whether a 39 mm watch is right for your wrist. Or look at the South in deep blue with your measurements to hand.

Strap fit and comfort

  • A strap should let one finger slide underneath without the case sliding around.
  • Leave a little room on hot days, when wrists swell.
  • Sit the case beside the wrist bone, not on top of it, so it does not press when you bend your hand.
  • Check strap length as well as case size. Very small or very large wrists may need a short or long strap.
  • If you are between two holes, the looser one is often more comfortable for long wear.
  • Wear the watch for a full day before you decide. Comfort at your desk can differ from comfort on a walk.

Measure once with care and you will rarely buy the wrong size again. Keep both numbers, circumference and flat-top width, in your phone for next time.

Frequently asked questions

How do I measure my wrist without a tape measure?

Wrap a strip of paper around your wrist where the watch sits. Mark the overlap with a pen and measure the strip against a ruler.

What matters more, case diameter or lug to lug?

Lug to lug usually matters more. It decides whether the watch sits within the flat top of your wrist or hangs over the edges.

Is a 39 mm watch too small?

Not usually. A 39 mm case is a classic field watch size. With a 46.5 mm lug to lug, it suits a wide range of wrists.

Where should a watch sit on my wrist?

Just beside the wrist bone, with the strap snug enough to stop the case sliding but loose enough to fit one finger underneath.

Does wrist size change during the day?

Yes. Wrists can swell slightly with heat, exercise and time of day, so measure later in the day for the most comfortable fit.

All four KOMPAS models share the same 39 mm case and 46.5 mm lug to lug. See the KOMPAS range.

Previous
Previous

What Is a Microbrand Watch, and Is One Worth Buying?

Next
Next

What Is Hacking Seconds and Why Does It Matter?